Black & Decker PP360 manual

Black & Decker PP360
9.2 · 1
PDF manual
 · 6 páginas
Español
manualBlack & Decker PP360
GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to follow all instructions listed below mayresult in electric shock, fire and/or serious injury. The term “power tool” in all of thewarnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the dustor fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions cancause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs andmatching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators.
There is an increased risk of electric shock if your body isearthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool willincrease the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damagedor entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication.
A moment of inattention while operating power tool mayresult in serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position before plugging
in.
Carrying power tools with your finger on the switch or plugging in power tools thathave the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench ora key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables bettercontrol of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught inmoving parts. Air vents often cover moving parts and should also be avoided.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of these devices canreduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power toolthat cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power toolaccidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use.
Many accidents arecaused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power tool,
SAVE THIS MANUAL FOR FUTURE
REFERENCE.

INSTRUCTION MANUAL

Catalog Numbers PP360, PP480

Cat No. PP360, PP480 Form #905169500 May-07 Copyright © 2007 Black & Decker Printed in China
taking into account the working conditions and the work to be performed.
Use ofthe power tool for operations different from those intended could result in a hazardous sit-uation.
5) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery pack.
Inserting thebattery pack into power tools that have the switch on invites accidents.
b) Recharge only with the charger specified by the manufacturer.
A charger that is suit-able for one type of battery pack may create a risk of fire when used with another batterypack.
c) Use power tools only with specifically designated battery packs.
Use of any otherbattery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal objects like paper
clips, coins, keys, nails, screws, or other small metal objects that can make a con-
nection from one terminal to another.
Shorting the battery terminals together maycause burns or a fire.
e) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help.
Liquid ejected from the battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
b) If the replacement of the supply cord is necessary,
this has to be done by the manufacturer or his agent in order to avoid a safety hazard.
Specific Safety Rules
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will
make exposed metal parts of the tool "live" and shock the operator.
Use clamps or another practical way to secure and support the work piece to a stable
platform. Holding the work by hand or against your body leaves it unstable and may lead to
loss of control.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min........................minutes ......................alternating
current
......................direct current
n
o ........................no load speed
..........................
Class II Construction
........................earthing terminal
....................safety alert symbol
...................... .../min ..................revolutions or
reciprocations
per minute
T
T
HANK
HANK
YOU
YOU
FOR
FOR
CHOOSINGCHOOSING
B
B
LACK
LACK

&

&

D
D
ECKERECKER
!
!
G
G
O
O
T
T
O
O
WWW
WWW
.B
.B
LACKANDLACKAND
D
D
ECKERECKER
.
.
COM
COM
/N
/N
EW
EW
O
O
WNER
WNER
T
T
O
O
REGISTERREGISTER
YOUR
YOUR
NEW
NEW
PRODUCTPRODUCT
.
.

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A
SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE
SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
Functional Description
1. Spindle
2. LED Light
3. Release Button
4. Forward/Reverse Button
5. On/Off Switch
6. Jack Plug
7. Charger
8. Charging Port
A
1
7
6
5
4
3
2
8
B
C
D
E

Manual

Ver el manual de Black & Decker PP360 aquí, gratis. Este manual pertenece a la categoría Máquinas de tornillos y ha sido calificado por 1 personas con un promedio de 9.2 . Este manual está disponible en los siguientes idiomas: Español, Inglés . ¿Tienes alguna pregunta sobre Black & Decker PP360 o necesitas ayuda? Haz tu pregunta aquí

¿Necesitas ayuda?

¿Tiene alguna consulta sobre el Black & Decker PP360 y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Black & Decker PP360 proporcionarle una buena respuesta.

Número de preguntas: 0

Black & Decker PP360 especificaciones

A continuación encontrará las especificaciones del producto y las especificaciones del manual del Black & Decker PP360.

General
Marca Black & Decker
Modelo PP360
Producto Máquina de tornillos
EAN 4306231111109
Idioma Español, Inglés
Tipo de archivo Manual de usuario (PDF)
Peso y dimensiones
Peso 500 g
Desempeño
Velocidad de giro al ralentí (máx.) 180 RPM
Tamaño de tornillo (max) 6.4 mm
Control de energía
Tecnología de batería Níquel-metal hidruro (NiMH)
Tiempo de carga 12 h
Voltaje de la pila 4.8 V
Fuente de energía Batería
mostrar más

Preguntas frecuentes

¿No puede encontrar la respuesta a su consulta en el manual? Puede encontrar la respuesta a su consulta en las preguntas frecuentes sobre el Black & Decker PP360 más abajo.

¿No aparece tu pregunta? Haz tu pregunta aquí

No hay resultados